Guide: How to install led spotlights, commonly used led spotlights can be installed around the ceiling, or can be installed in the upper part of the furniture, or placed in the wall, wall skirt or skirting. The light of the led spotlights is generally illuminated on the required objects, so that the items illuminated by the lights are bright and beautiful, and the artistic effects of focusing, unique environment, rich layers, rich atmosphere and colorful colors are achieved. How to install led spotlights, soft lighting lines, graceful and luxurious, spotlights can not only make the overall lighting effect good, but also local lighting, setting off the atmosphere. Xiaobian to tell you about the 8 steps to install LED spotlights, learn together!
Led spotlight
How to install led spotlights
First, how to install led spotlights, process:
Light stand, lamp installation and connection down line test light
Second, how to install led spotlights, lamp holders, lamps installed:
1. Measure the installation height of the lamp (light stand) according to the design requirements, and mark the pole on the pole.
2. Lift the lamp holder and the lamp on the pole (heavier lamp holder, lamp can use the pulley, big rope to hang the pole), put on the hoop or bolt, find the angle of illumination according to the design requirements, find the level of flatness After that, fasten the lamp holder.
3. The elevation angle of the lamps installed in rows should be consistent and neatly arranged.
Third, how to install led spotlights, matching down the line:
The pin insulator is fixed on the lamp holder, and one end of the wire is tied to the insulator and connected to the lamp line and the fuse respectively. The rubber cloth and the black rubber cloth are half-overlapped and each layer is covered. Then, the other end of the wire is tightened and wounded with the back of the street lamp trunk.
8 steps to install LED spotlights
The eight steps to install an LED spotlight are as follows:
1. Process flow: lamp holder, lamp installation → matching down line → test light
2. Installation of lamp holders and lamps:
1) Measure the installation height of the lamp (light stand) according to the design requirements, and mark the pole on the pole.
2) Hang the lamp holder and the lamp on the pole (heavier lamp holder, the lamp can use the pulley, the big rope to hang the pole), put on the hoop or bolt, find the angle of illumination according to the design requirements, find the correct After the degree, tighten the lamp holder.
Led spotlight
3) The luminaires installed in rows should have the same elevation angle and neatly arranged.
3. Matching the down conductor: Fix the pin insulator on the lamp holder, tie one end of the wire to the insulator and connect it to the lamp line and fuse respectively. The rubber cloth and the black rubber cloth are half-overlapped and each layer is covered. Then, the other end of the wire is tightened and wounded with the back of the street lamp trunk.
4. The phase line of the luminaire should be equipped with a fuse, and the phase line should be connected to the center terminal of the screw base.
5. The connection point between the line and the street lamp trunk line should be 400~600mm from the center of the pole, and the two sides are symmetric.
6. There should be no joints in the volley section of the down conductor. The length should not exceed 4m. If it is exceeded, it should be installed with a fixed point or using steel pipe leads.
7. The wire should be covered with a soft plastic tube at the entrance and exit of the lamp holder, and the waterproof bend should be made.
8. Test light: After all the installation work is completed, send and test the lamp, and further adjust the illumination angle of the lamp.
How to buy LED spotlights
The spotlights are divided into low voltage and high voltage. Consumers should choose low-voltage spotlights, which have a longer life and higher light efficiency. The light effect of the spotlight is reflected by the power factor. The greater the power factor, the better the light effect. The power factor of the ordinary spotlight is about 0.5, the price is cheap, and the power factor of the high-quality spotlight can reach 0.99, and the price is slightly expensive.
Spotlights are generally used to enhance the illumination of decorative objects. They are usually embedded in ceilings or walls. When spotlights work, they generally emit higher temperatures. Therefore, it is necessary to purchase high-quality products, otherwise there will be safety hazards.
When using the spotlight, it should be used with the transformer. The lamp bead should also be of good quality. Otherwise, the lamp bead of the spotlight is very easy to break. Think about it, the spotlight lamp bead in the ceiling can be quite troublesome to replace.
The quality of the spotlights on the market is not good enough. It is difficult to distinguish between good and bad by the naked eye. Therefore, it is best to choose the brand products for the spotlights and choose the high-quality transformers.
Fiber Optic Equipment,Cctv Ip Camera Splitter,12V Waterproof Poe Splitter,Ftth Fiber Optic Patch Cord
Shenzhen Scodeno Technology Co.,Ltd , https://www.scodenonet.com